Skip to main content

Barium Strontium Titanate Sputtering Targets and Applications

Barium strontium titanate (BST) is a solid solution of barium titanate (BaTiO3) and strontium titanate (SrTiO3).
Barium strontium titanate (BST) thin films obtained by sputtering methods gives excellent dielectric properties to materials. Because of this, barium strontium titanate (BST) based ferroelectric thin film devices have been popular over the last decade due to their versatile applications in tunable microwave devices such as delay lines, resonators, phase shifters, and varactors.
Barium strontium titanate thin films are promising candidates due to their high dielectric constant, tunability and low dielectric loss. Dielectric-tunable properties of barium strontium titanate films deposited by different deposition techniques have been reported which study the effects of factors, such as oxygen vacancies, film thickness, grain size, Ba/Sr ratio, etc. Researchers have also studied doping concentrations, high temperature annealing and multilayer structures to attain higher tunability and lower loss.
You can find out many researches done about barium strontium titanate sputtering. Here are some links from these studies:
If you need barium strontium titanate sputtering targets for your research needs, you may order from the links given on the table below:
TypeSizeThicknessPurityLink
Barium Strontium Titanate2'0.125''99.99%https://nanografi.com/sputtering-targets/barium-strontium-titanate-elastomer-bao4srti-sputtering-targets-size-2-thickness-0-125-purity-99-99/
Barium Strontium Titanate3'0.125''99.99%https://nanografi.com/sputtering-targets/barium-strontium-titanate-elastomer-bao4srti-sputtering-targets-size-3-thickness-0-125-purity-99-99/
Barium Strontium Titanate3'0.250''99.99%https://nanografi.com/sputtering-targets/barium-strontium-titanate-elastomer-bao4srti-sputtering-targets-size-3-thickness-0-250-purity-99-99/
Barium Strontium Titanate4'0.125''99.99%https://nanografi.com/sputtering-targets/barium-strontium-titanate-elastomer-bao4srti-sputtering-targets-size-4-thickness-0-125-purity-99-99/
Barium Strontium Titanate4'0.250''99.99%https://nanografi.com/sputtering-targets/barium-strontium-titanate-elastomer-bao4srti-sputtering-targets-size-4-thickness-0-250-purity-99-99/
Barium Strontium Titanate6'0.125''99.9%https://nanografi.com/sputtering-targets/barium-strontium-titanate-elastomer-bao4srti-sputtering-targets-size-6-thickness-0-125-purity-99-99/
Barium Strontium Titanate6'0.250''99.9%https://nanografi.com/sputtering-targets/barium-strontium-titanate-elastomer-bao4srti-sputtering-targets-size-6-thickness-0-250-purity-99-99/
Barium Strontium Titanate8'0.125''99.9%https://nanografi.com/sputtering-targets/barium-strontium-titanate-elastomer-bao4srti-sputtering-targets-size-8-thickness-0-125-purity-99-99/

Comments

Popular posts from this blog

Usage of Silver Conductive Adhesive Paste in Corrosion Protection

In electronics, solders are main material to connect electrical components to substrates which are generally printed circuit boards. Although they are cheap, they are not effective if long term performance is considered since solders have low resistivity to corrosion relatively. Since corrosion reduce reliability, the cost of advanced technological systems such as RADAR, SONAR, LIDAR and more increase. In addition, small signals can be lost, and in huge data transfer, some of the data can be lost also especially which may lead catastrophic failures in critical systems. For instance, surface to air missiles can be launched to target which is not exist if the data coming from detection systems is noisy. Therefore, corrosion protection is necessary, and  silver conductive adhesive paste  is an essential candidate to replace PbSn solders due to its resistivity to corrosion. Silver conductive adhesive paste provide not only noisy reduction but also electromagnetic interference whi...

Reduced Graphene Oxide and Applications

Graphene oxide (GO)  is a type of graphene that contains oxygen functional groups and has some interesting properties different than those of graphene. By reducing graphene oxide,  reduced graphene oxide  is obtained which is abbreviated to rGO. In this process, the functional groups of graphene are removed but it still contains residual oxygen, hetereatoms and structural defects which decrease its quality. Having less-quality compared to pristine graphene, rGO is still an outstanding material for various applications since it resembles an attractive cost and manufacturing processes compared to the pristine graphene. Especially, it is preferred in applications that call for a large amount of material. Depending on the method of preparation of reduced graphene oxide, properties and morphology of the rGO can vary.  Some preparation methods  of reduced graphene oxide include: treating graphene oxide with hydrazine hydrate at 100°C for 24 hours exposure to h...

Nanocellulose: Descriptions, Usage and Applications

Nanocellulose  is denoted by nano-structured cellulose which consist of C6H10O5. Since cellulose is abundant polymer in nature, large quantity of nanocellulose can be manufactured from the cost-effective aspect. Non-toxic and lightweight properties make it easy to carry, so it can be used in applications which requires mobility. High tensile, stiffness and electrical conductivity expand its usage through electrical and mechanical applications. Unique properties depending on the type of nanocellulose are also exist. There are three types which are cellulose nanocrystal (CNC), cellulose nanofibers (CNF), and bacterial nanocellulose (BNC). First type of nanocellulose is  cellulose nanocrystal , development in applications show that CNCs have unique specialities for improving mechanical properties of nanocomposites such as electrospun nanocomposite fibers/mats and nanocomposite hydrogels. Numerous nanocomposite hydrogels reinforced with CNCs can be designed to be sens...